NITROUS KITS FOR MOTORCYCLES
NitroBoost Nitrous Systems
NITROBOOST BENEFITS:
1: Fits any motorcycle or ATV.
2: Most affordable way to add HP.
3: Very simple to install.
For Street or Strip, HardRider has you covered. HardRider's NitroBoost provides "DRY & WET" premium products have been chosen with experience and are provided with braided, copper or galvanized steel lines, premium solenoids and first class fittings and bottles etc.
NitroBoost Kits will NOT become obsolete as you go higher in power and accessories. HardRider can assist you with every step, whether its controllers, heaters or bottle fills.
Most riders prefer a smaller bump in power 15-40hp. If you are adding up to 40-60hp, a power commander will suffice to add more fuel with maps you can download (link on our tutorial page), providing correct AFR (air fuel ratio) ensuring your engine is safe from running to lean. Running a small hit of nitrous (15-40hp) to the air box, the air sensors will adjust for the nitrous and add a slight increase in fuel. This is only for dry kits as wet kits are delivering fuel and nitrous together.
Wet kits are generally for carbureted engines, but in some cases needed for EFI engines where there are much, much higher demands for nitrous adding 100+hp. Dry kits rely solely on the motorcycles injectors and the fuel pump to provide more fuel and if either of these are unable to deliver more fuel, then the engine runs lean and ends with severe engine problems. Small nitrous increases no issue, moderate usually requires a stronger fuel pump, adding even more nitrous requires more efficient injectors. Adding a lot of nitrous 100+hp usually will require a wet kit that has its own dedicated fuel pump and solenoid which provides nitrous and fuel together to ensure compatible fuel delivery. Go to our Tutorial Page for more info. Motorcycle nitrous kits.
NITROBOOST KITS
NitroBoost Basic Dry Kit - Comes with everything you need for a complete installation including a black powder coated 1.25lb. nitrous bottle with high flow valve and burst safety pin, stainless steel solenoid with high power coil use 1/8"npt inlet/outlet ports with .078" orifice, 4 foot 4AN steel braided line from bottle to solenoid, 3 foot steel braided line from solenoid to air box, spray fogging nozzle, all necessary fittings, bottle clamp, 3 jets 15-20-30), wiring and instructions. Optional 2.5lb bottle, larger jets, extra feed line and fittings. Use as is, or add products below as needed.
NitroBoost Custom Wet Kits - Unlike Dry Kits that are quite simple, wet kits require additional fuel delivery, requiring an additional fuel solenoid, plus a fuel pump to provide that fuel. Additionally it requires separate fuel and nitrous lines for each cylinder. Wet kits are used for all carbureted engines and require the wet kit fogger shown below to be tapped into the carbs. Because wet kits are more complex, they are custom order only.
Dry Kit with 1.25lb. Bottle - $390
Dry Kit with 2.5lb. Bottle - $430
NITROBOOST BOTTLES
HardRider provides a choice of two premium aluminum nitrous bottles for your motorcycle, either 2.5lb or 20oz. bottles. This choice comes down to install location and look. Bigger bottles give more longevity and some riders get around this by adding a second bottle in the smaller size. Bottles come with High Flow Valve and Burst Safety Valve.
The Green Hornet busa below, uses 2-2.5lb. bottles, with premium frame mounts. HardRider also provides 10lb bottles for automobile use or as a mother bottle to fill the smaller bottles.
All HardRider NitroBoost bottles come in powdered coated black with high flow valve and syphon tube (not installed).
Purchase 1.25 lb. bottle - $159
Purchase 2.5 lb. bottle - $199
Purchase 10 lb. bottle - $299
NITROBOOST SOLENOIDS
NitroBoost solenoids are manufactured using a proprietary plunger material that is swelling resistant. Crafted with a strong stainless steel base, these solenoids are a staple in the high-performance market. The primary purpose of a solenoid is to act as a valve turning the nitrous and fuel on and off. Different sizes of solenoids are available depending on the amount of flow required. Only use a PTFE thread sealant paste to seal fittings.
High Flow Nitrous Solenoid Standard .078 orifice - $159
High Flow Nitrous Solenoid Premium .09 orifice - $189
High Flow Fuel Solenoid Premium .178 orifice - $199
NITROBOOST BRAIDED LINES
Perfect for nitrous solenoid. 4AN and 3AN female to 1/8" npt male. NitroBoost stainless steel braided hoses are PTFE-lined and factory-assembled to provide safe, secure plumbing for your nitrous and fuel line needs. The hoses are available in a variety of lengths, diameters, end fitting sizes and thread attachment styles. Hose ends are offered with a red, blue, or black anodized finish. Stainless AN lines have anodized fittings with a Teflon lined inside of the fitting to unsure no leaks. Copper lines custom by quote.
4AN Stainless Steel Braided Line 4 Ft - $49
NITROBOOST COPPER LINES
Copper lines are quickly becoming the go-to choice for nitrous lines. The most obvious advantage of copper lines is that they are much more durable, flexible and stronger. Furthermore, since they are made from a flexible material, they can bend around tight corners with ease. Copper is also more resistant to temperature fluctuations than other metals, allowing it to maintain its performance even in extreme temperatures and it does not absorb as much heat as other materials. More than anything, copper lines are designed to offer maximum efficiency by allowing for greater flow. HardRider provides made to measure custom copper lines with fittings. Copper are custom prepared priced by quotation only.
NITROUS BRACKETS & ACCESSORIES
Bottle brackets are important to work properly and look good at the same time. Our brackets do both. High quality aluminum in a wide range of sizes. Whether you are installing on tabs, a flat surface or clamping to a tube; the billet aluminum bar clamps are an ideal solution for mounting just about any accessory. Natural aluminum finish or powder coated black.
For custom fittings, tell us what you are looking for and we will get back to you. Send us your requirements by filling out the form in our Purchase/Enquiry section.
Motec Dual Lambda
The C125 is a popular model in MoTeCs range of colour Displays and Display Loggers. Striking in design and powerful in functionality, the C125 offers display, data logging, auxiliary control and programmable LEDs all in one compact device. The vivid 125mm screen (approx 5″) is high resolution with up to 32Gig of logging capacity.
MoTec LTC (Lambda to CAN) modules monitor, control and diagnose Bosch LSU 4.9 Lambda sensors, transmitting readings on a CAN bus. When multiple LTCs are used, up to 32 Lambda sensors can be configured on a single CAN bus, allowing a CAN-enabled ECU or logging device to simultaneously monitor numerous Lambda sensors. The LTC is also available as a dual version LTCD to work with two sensors into one module. Send us your requirements by filling out the form in our Purchase/Enquiry section.
NITROUS MOTHER BOTTLE NUT
The mother of all nuts, this fitting goes on the mother bottle, usually a 10 or 15lb. bottle for motorcycle usage. This has the male 4AN end for the 4AN braided line for filling the smaller bottles. Fitting $14
NITROUS BOTTLE PRESSURE GAUGE
Liquid Filled Nitrous Pressure Gauge 1.5" with white face and chrome bezel. Mount this show quality gauge on your bottle so you can keep an eye on that bottle pressure. Comes with 1/8" NPT male output fitting so it can screw right into the side of your bottle port. Gauge $59
NITROUS AIR FUEL GAUGE
If you are running any kind of motorcycle modification like nitrous, turbo, supercharger etc, you are going to require an AFR air/fuel gauge to keep your ratio in the correct zone. This gauge will let you know if for whatever reason your ratio is not correct and to shut down and re-tune. Problem could be a bad injector, fuel pump or in the case of a nitrous kit, too much nitrous and not enough fuel. With this gauge installed you do not need to worry about damaging your engine.
Note: You must use a heat sink bung for turbo or supercharged applications! See below. Gauge Complete $399
LC-2 Lambda Cable (Standalone Wideband Controller) with wideband 02 Sensor and Billet round 2-1/16" display in a stand alone package deal. Comes with everything you need even the weld on bung. No computer needed as this kit is stand alone and ready to go. Bosch Wideband Sensor Included. The LC-2 is a complete wideband controller. It features the same award-winning patented digital measurement principal found in the LM-2, and includes digital input, output, and 2 programmable analog outputs. Can optionally be programmed to output data or be configured to work with aftermarket fuel injection systems.
HIGH TEMP HEAT SINK BUNG
Heat-Sink Bung Extender (HBX-1) The Bosch LSU4.2 wide-band O2 sensor (shipped as part of the LM-1 kit) is rated to operate at an exhaust gas temperature of < 1300 degrees (F), and a sensor housing temperature of < 900 degrees (measured at the bung) for maximum accuracy and control. When either of these operating temperature ranges is exceeded, the sensor can no longer be accurately controlled. The LM-1 is designed to display an error message under these conditions (currently 08- Sensor Timing Error) rather than provide inaccurate readings. Sensor $149
FUEL PRESSURE GAUGE
Seeing the exact fuel pressure on your vehicle can mean the difference between extracting the most performance safely and expensive failures. Autometer's digital stepper motor fuel pressure gauge will precisely measure your exact fuel pressure at levels of accuracy previously unheard of even in professional gauges. Designed for fuel injected or carbureted applications, our advanced 1/8" NPT solid state pressure transducer provides the best possible measurements on the market with unparalleled resistance to vibration and heat. Don't take chances with your investment; a precise fuel pressure gauge could be the cheapest insurance you've ever bought. This meter is a must! Fuel Gauge $99
NITROUS STANDARD FITTING
Male to 1/8"NPT Male Fitting standard fitting in 3AN or 4AN. A very standard fitment. for nitrous.
Fitting $9
NITROUS TWO PORT ADAPTER
Two Hole Gauge Adaptor 4AN swivel. Use this custom fitting for all gauges and nitrous bottle heater kits to mount the pressure switch. The two ports are 1/8"npt female. Comes with one hole plug just in case you only need one port. Fitting $19
NITROUS JET FITTING
This fitting holds a standard NOS style flare jet. A -3AN braided line attaches over the jet and screws onto the fitting to seal and secure the jet in place. You can use this fitting for dry nitrous applications into air box's, manifolds etc. Fitting $14
NITROUS 90 DEGREE NOZZLE
Convenient fitting for nitrous feed line to get into the right places or redirect to better angles. Let's your line come out a better angle for some installations. 4AN and 3AN. Fitting $12
NITROUS SPRAY NOZZLE
This fogger spray nozzle is used for Dry Nitrous injection. It has a 1/16" NPT threads, see our tap for mounting. Fitting $45
DISTRIBUTION BLOCK SPYDER
These distribution blocks come as shown with the 3/16" compression fittings to work with the fogger tubing. Fitting $69
WET KIT FOGGER
Fogger nozzle for wet nitrous kits. See our tap to make mounting a snap. Fitting $69
FUEL PUMP FOR WET KIT
Fuel Pump used for Wet Nitrous Kits. Pump $139
TAP FOR WET KITS
1/16" NPT tap for Fogger Nozzle Installation into metal or thick plastic. Use drill bit "D" or a .246" drill bit. Tap $19
GENERAL SWITCHES
Set of 3. Perfect for custom wiring or switch replacement, The Toggle Switch has a red safety cover to prevent accidental activation. Blade-type terminals facilitate easy wiring and installation. Switches $39
NITROUS PURGE LIGHT
This Device will illuminate your purge for a dramatic effect at night! Five super intense LEDS will last for years and years without failure. 1/8" steel Tubing fits through the center of LEDS and a set screw secures it in place. Light $129
NITROUS BOTTLE HEATER
This Bottle heater (for 20oz / 2.5LB bottles) is one of the best available and uses the smallest most accurate pressure switch available. Our heater holds the pressure within 50 PSI. It comes with all the components to install and is made out of superior components! It will keep your bottle at an optimum pressure 900-950 PSI(adjustable from 550-1250PSI). The heater is a full silicone flexible heater with velcro straps for quick bottle changes. Team this up with our pressure Gauge you have the most sophisticated nitrous pressure control system available. Element size 12.75"x3.
Warmer Controller Kit $299
NITROUS JETS
Buy What You Need. Our Nitrous jets are precision machined to create a perfect flowing jet. Our jets only work with our kits. Jets have numbers stamped into the sides of them. The number is the size hole that is drilled in the jet. Example, a #28 jet has a .028" hole in it. Jets can be used for nitrous or fuel. When the jetting chart calls out for a #58 Nitrous jet and a #32 fuel jet, simply buy a #58 and a #32 jet. See chart below on this page. Jets $6 each
MINI CONTROLLER
The Mini Controller is a 2-stage progressive nitrous controller featuring two independent stages of nitrous control, each with its own throttle position activation switch and progressive control ramps. It eliminates the need for a window switch, and allows you to turn the nitrous on and off at set points.
The controllers also feature two programmable outputs so you can control timing retard or other devices. Includes hand-held touch screen programmer which makes it quick and easy.
Features:
-2 fully independent nitrous controllers in one bulletproof case
-Hand held programmer for ease in programming. Allows you to mount the main box out of sight. Integrated throttle position activation switch eliminates the need for a separate WOT switch.
Progressive nitrous ramps feature:
-Delay time programmable from 0 to 9.9 sec.
-Start percentage programmable from 0 to 99%
Ramp time programmable from 0 to 9.9 sec
-End percentage programmable from 0 to 99%
Nitrous can be programmed to ramp up or down
-RPM on/off control eliminates the need for a separate window switch
Solenoid control channels with a 40 amp load capacity for large solenoids
-Two output signals for use with timing retards or activation switches
Controller $399
NITROUS BOTTLE SCALE
Our Nitrous scale comes with two weighing capacity choices of 60lb, 110lb depending on your needs. Start Weight from 10g/0.5oz. Our scale has a graduation of 0.1oz. and can be powered by batteries. Comes with USB cable, and AC adapter. Tare function which allows you to zero out the number for the previous weighing objects. Hold function allows you to lock the number after you take the package off the platform. It's critical to fill bottles to the correct weight and extremely important not to over fill. Over filling will cause the bottle pressure to rise out of the safety zone and will also damage solenoids. Bottles do have safety burst valves.
Scale $79
FLARING TOOL KIT
Nitrous Line Flaring Tool Kit for setting various angles on copper, or galvanized steel lines with 45° flares for correct fitting. This 45° flaring and swaging kit comes with cones, bars, fittings, tube cutter, and ratchet wrench features sizes ranging from 1/8” to 5/6” to ¾” and case. It even comes with ¾” OD tubing to ensure consistent repairs. Flaring Tool Kit $99.
BRAIDED LINE FITTING KIT
The set includes one AN 4 to AN 8 sizes. Kit fits -4AN though -8AN fittings and hoses. Eases braided hose and fitting assembly. Kit include all tools, fitting adapters for most fittings, detailed assembly instructions and storage case. Kit fits -4an though -8an fittings and hoses. Eases braided hose and fitting assembly. Includes detailed instructions including video. Braided Line Cutter Fitment $179
Nitrous Jet Size Approximates
